↓In my tantrum(s) at the feathers not looking right, I took them out, and put them back in, about 7 times, not easy, as I had to slice under to get them off, then hope I didn’t tear anything on it’s way out, and hope I didn’t fudge the amount under the top layer of feathers on the way back in.

↓ Proof I did actually get it all together, and looking good. this is just the wings

↓ It took a bit of doing, trying to figure out the best way to do the teeth for the cogs for the top gear, I finally went strips of evenly rolled clay, cut to the same size little squares, and stacked them so they were as even as possible without measuring too much.

↓ I ran out of the special mix and & black clay while workin on the top part, so I grabbed some chunks of scrap out of one of my three (yes three) shoeboxes full of scraps. The scraps, when I rolled them out, had some bits of canes left on them. The face you see in the right sheet is from an old ‘goth girl’ cane from, um, over 5 years ago, possibly 6 or 7. I’ll have to find some of my old canes, I know I have a box somewere of some I’ve worked on over the years.. Anyways, back to the ahnk

↓ I guess you could call this the final draft. the wings are done, the cogs cut and ready to place. I just need to squish the top teeth in, smooth everything out, and give the bottom cogs some height, so they’re more even with the others. I’m thinking of using one of three ideas for the background. One, a generic texture, something that isn’t too buzy and won’t clash with the feathers. Two, painting something to go with the clockwork ankh. Three, using some of my scrap mokume gane from an old project. It’s pretty sweet, gold leaf and translucent, so it’s quite the shinny. The background will all depend on what the finished piece is going to look like, and that hasn’t been decided yet.

Tomorrow will be dedicated to finishing the piece, then working out how to bake it. I’m not 100% it’ll fit in our oven!

↓base layer of clay on, checking layout with a few clay pieces & one of the paper templates

↓another layout check, this time with most of the clay bits, all laid out

↓took all the gears off, and got a thicker even layer for the wings, using wax paper to try to keep it as even as possible

↓wing segments drawn in, along with detail started on top left feathers

↓most of the top left feathers done

↓all the feathers done (except for the top two)

↓ showing the detail in the feathers

↓with the gear pieces to check how it’s all pulling together, make sure it’s correct & all

That was all done between about 3ish am and 9am (I say 3ish, as I didn’t check a clock on my way back out)
Going back out to the studio now to work on the bottom layer of feathers, then to tackle the top gear segment & see how it pulls together, then there’s the thinking on what to do about the background.

SALE IS OVER!

So, me making it to the Maker Fair isn’t happening. In trade, my other half helped chip in for a studio!
Yes, a real studio just for me!

Originally, we were looking around, but not sure what to get, then, finally figured out what I wanted, and what would fit. Then it was a matter of pricing. Lowe’s and another local place wanted decent credit, and well, my credit, though in repair, and getting better, is not good enough for a building. So, we went another route.
There’s a local place here in Athens, TN, the Athens Barn Center. They rent to own, with no credit check! So, after looking around their lot a few times, I knew what I wanted, but they didn’t have one the size I wanted. No fear! They also build custom! Hell yah!
So, I had a custom Side Lofted Barn built, with a single door and two windows. It would have been here a week ago if not more sooner, but the weather has disagreed with me.
I’ve been totally impatient, waiting, but it finally got here today! I got a slight sunburn helping direct the driver in with it. Due to trees, it wasn’t put in the spot I wanted, but close enough!

This weekend, we’ll be going to Home Depot (Lowe’s turned me down) to get insulation, and the wiring needed to wire it up for electricity! (yay!)
Here’s some photos of what it looks like, and I’ll be posting more as it gets finished!

I’m also offering some major bonuses in my Etsy stores! (ZKitten and Chaotic Supplies)

ALL Orders
over $25 get free FC shipping!
over $50 get free priority shipping!
ALL orders
under $20 get a small bonus gift!
over $20 get a medium bonus gift!
over $50 get a medium/large bonus gift!
over $75 get a large bonus gift!
over $100 get multiple large bonus gifts!
ALL orders
over $20 get a certificate for 10% off their next order!
over $50 get a certificate for 20% off their next order!
over $100 get a certificate for $25 off their next order!

If I can work up enough money where I know I’ll be able to make it (about $500 by late April) I’ll also be the organizer for, and bringing items from various SteamTeam members from all over the world!

i just found out one of my friends, one of the few people i would trust with just about anything, committed suicide.

i’ll be donating 50% of what I make at this v-day bash on saturday to samaritansri.org

i’ll also be donating 50% of what I make for the next two weeks from either of my etsy stores.

if you aren’t interested in buying something from me, i’d really like it if you could make a donation to them yourself.

http://www.samaritansri.org

Final Total: 599,
yes 599 gears in a 2.5″X1″X1″ container!

On to the winners!

Second Place-
DBVictoria (of Designs by Victoria) who had a guess of 697 and Dr. In Sectus of (In Sectus) with a guess of 527

Third Place-
Barbarella-The Mad Cat Lady (of CatNip Camera) who had a guess of 731 and Eve (of Saint Tattoo) with a guess of 402

And The Winner-
with a guess of 597 is Amber G!
She has won a $50 gift certificate!

I hope all of you had fun! The next Contest will be in March!